My BassHorn VS Martin WSX |
Post Reply | Page <1 678910 15> |
Author | |
mstep77
Registered User Joined: 19 July 2006 Status: Offline Points: 457 |
Post Options
Thanks(0)
|
nice design mate, that is gonna be seriously loud.
One thing to note with designs with two drivers in (assuming they are wired in parallel and are 8R) is that the box will have an overall impedance of 4R (as I'm sure you know) so in hornresp you should set the input voltage to 2V instead of 2.83V to give the true 1w/1m reading. obviously the box will have twice the power handling though Best regards, Matt |
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
Yes. There is no rear chamber.. Drivers are in open air... |
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
I think, it can be a good change of LABs... Much lower bass... It looks like dual inverted scoops whith a small throat chamber... Edited by Amano - 27 November 2008 at 6:47pm |
|
wafflesomd
Young Croc Joined: 21 September 2007 Status: Offline Points: 811 |
Post Options
Thanks(0)
|
Doesn't look like the lower driver would come out after its put in.
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
In december i'll try to build this one.... and i'll compare it with WSX, dual WSX at same power lever...
|
|
tommysb
Registered User Joined: 24 April 2006 Location: Finland Status: Offline Points: 1036 |
Post Options
Thanks(0)
|
What happens to the excursion at higher powers?
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
At power level of 650Watt per driver excursion at 40Hz is +-6,2mm, at 62hz is +-6,8mm..
It's possible to change the driver.... putting RCF LF18N401 |
|
MarjanM
Old Croc Joined: 10 February 2005 Location: Macedonia Status: Offline Points: 7816 |
Post Options
Thanks(0)
|
This box can not go as low as a lab sub. It is short for about 1,2m of horn length. |
|
Marjan Milosevic
MM-Acoustics www.mm-acoustics.com https://www.facebook.com/pages/MM-Acoustics/608901282527713 |
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
~2.1 meters! ...
|
|
Deadbeat
Old Croc Joined: 12 March 2008 Location: Singularity Status: Offline Points: 3167 |
Post Options
Thanks(0)
|
Lab? You will have to beat this in 2pi .
And they're using 2xLAB12s. Your horn is a nice design. However, keep this in mind: Stacking the horns side by side so a tunnel is formed with the open back may change quite a bit in terms of acoustic impedance on the other side of the cone, and delay of the 'back wave' by differing amounts. Now, what settings are you using for combined response? |
|
Away on extended leave.
|
|
tommysb
Registered User Joined: 24 April 2006 Location: Finland Status: Offline Points: 1036 |
Post Options
Thanks(0)
|
What software is that Deadbeat?
Tom |
|
TDA-Audio
Registered User Joined: 11 February 2005 Location: Russian Federation Status: Offline Points: 294 |
Post Options
Thanks(0)
|
based old project http://www.speakerplans.com/forum/forum_posts.asp?TID=8740 |
|
horns plans http://photofile.ru/users/tda-audio/
|
|
Post Reply | Page <1 678910 15> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |