Speakerplans.com Homepage
Forum Home Forum Home > Plans > Other plans
  New Posts New Posts RSS Feed - Database simulation
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Database simulation

 Post Reply Post Reply Page  <1 212223
Author
Message
tv00 View Drop Down
Old Croc
Old Croc


Joined: 10 August 2009
Location: Denmark
Status: Offline
Points: 1886
Post Options Post Options   Thanks (0) Thanks(0)   Quote tv00 Quote  Post ReplyReply Direct Link To This Post Posted: 20 April 2016 at 2:15pm
I think all you got to do is to add cone & cutout volume to rearchamber, and remove reardriver volume from frontchamber. (cutout volume depends on from which side driver is mounted. Remember polarity might be reversed (or not if phase shifts at crossover freq)
www.facebook.com/babysoundsystem
Back to Top
Junior253 View Drop Down
Registered User
Registered User


Joined: 08 September 2015
Status: Offline
Points: 46
Post Options Post Options   Thanks (0) Thanks(0)   Quote Junior253 Quote  Post ReplyReply Direct Link To This Post Posted: 22 April 2016 at 8:55am
thank a lot for your response
Back to Top
mhtplsh View Drop Down
Registered User
Registered User


Joined: 27 August 2007
Status: Offline
Points: 112
Post Options Post Options   Thanks (0) Thanks(0)   Quote mhtplsh Quote  Post ReplyReply Direct Link To This Post Posted: 24 June 2017 at 3:37am
Originally posted by bitzo bitzo wrote:

Mt121 without any horn for 2" compression driver

s1=360.8
s2=872.2
con=25.3
s3=1944
con=21
vrc=17.6
lrc=14.8
fr=0
tal=0
atc=1108
vtc=615.75


I am not able to understand how atc 1108 is calculated here.
Herewith posting picture with detailed drawing. of MT 121.
 
Back to Top
Daniel Twellmann View Drop Down
Registered User
Registered User
Avatar

Joined: 02 October 2011
Location: Denmark
Status: Offline
Points: 48
Post Options Post Options   Thanks (0) Thanks(0)   Quote Daniel Twellmann Quote  Post ReplyReply Direct Link To This Post Posted: 08 July 2017 at 8:45am
14cm*14cm*pi*1.8cm = 1108cm^3
Back to Top
Contour View Drop Down
Young Croc
Young Croc


Joined: 03 March 2004
Status: Offline
Points: 620
Post Options Post Options   Thanks (0) Thanks(0)   Quote Contour Quote  Post ReplyReply Direct Link To This Post Posted: 08 July 2017 at 9:24am
Atc should be an area not a volume?
Back to Top
Daniel Twellmann View Drop Down
Registered User
Registered User
Avatar

Joined: 02 October 2011
Location: Denmark
Status: Offline
Points: 48
Post Options Post Options   Thanks (0) Thanks(0)   Quote Daniel Twellmann Quote  Post ReplyReply Direct Link To This Post Posted: 08 July 2017 at 2:17pm
Yes, I just showed how 1108 was calculated :)

ATC and vtc should be switched around

Edited by Daniel Twellmann - 08 July 2017 at 2:18pm
Back to Top
mhtplsh View Drop Down
Registered User
Registered User


Joined: 27 August 2007
Status: Offline
Points: 112
Post Options Post Options   Thanks (0) Thanks(0)   Quote mhtplsh Quote  Post ReplyReply Direct Link To This Post Posted: 11 July 2017 at 2:01pm
From where you use 1.8 in the calculations. The plywood here is 12mm thick.
Please let me know what do you mean by ATC and vtc should be switched.
Back to Top
Alexandre 25 View Drop Down
New Member
New Member


Joined: 26 October 2019
Location: france
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote Alexandre 25 Quote  Post ReplyReply Direct Link To This Post Posted: 26 October 2019 at 4:29pm
Hello everyone

I am looking for akabak curve for the Beyma sb12,sb15 with the script if you have this.

have a good day
Back to Top
 Post Reply Post Reply Page  <1 212223

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2023 Web Wiz Ltd.

This page was generated in 0.063 seconds.