186 Cutlist.

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

So does anyone have a cutlist for them?....

Just kidding.

I went ahead and drew one out today.  It's probably not the most efficient cut list, but it's what I'll be using.  The list is for four cabinets.  I don't see the point in building any less.

I've labeled the pieces with letters that correspond with a picture I've included.

http://www.mediafire.com/?0oqwziixmwi

Edited by wafflesomd - 14 October 2008 at 10:49pm

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
wafflesomd Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 21 September 2007 Status: Offline Points: 811	Post Options Post Reply Quote wafflesomd Report Post Thanks(0) Quote Reply Topic: 186 Cutlist. Posted: 14 October 2008 at 10:48pm
	So does anyone have a cutlist for them?.... Just kidding. I went ahead and drew one out today. It's probably not the most efficient cut list, but it's what I'll be using. The list is for four cabinets. I don't see the point in building any less. I've labeled the pieces with letters that correspond with a picture I've included. http://www.mediafire.com/?0oqwziixmwi Edited by wafflesomd - 14 October 2008 at 10:49pm

breakdabeat pete Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 10 March 2008 Location: norwich Status: Offline Points: 753	Post Options Post Reply Quote breakdabeat pete Report Post Thanks(0) Quote Reply Posted: 14 October 2008 at 10:53pm
	it might seem silly but i usually draw out a 8' by 4' grid on a bit of paper then cut out all the pieces of wood on paper to scale then just play around saves rubbing out all the time
	٩(̾●̮̮̃̾•̃̾)۶

Sinfinity Members Profile Send Private Message Find Members Posts Add to Buddy List Old Croc Joined: 06 July 2008 Status: Offline Points: 1632	Post Options Post Reply Quote Sinfinity Report Post Thanks(0) Quote Reply Posted: 14 October 2008 at 11:02pm
	Or try http://www.delphiforfun.org/programs/cutlist.htm had a play with it two days ago. Seems to work. Free download. Should probably have done this before building my cabs. Might have saved some ply.
	Matt at ukamp dot co dot uk

wafflesomd Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 21 September 2007 Status: Offline Points: 811	Post Options Post Reply Quote wafflesomd Report Post Thanks(0) Quote Reply Posted: 14 October 2008 at 11:28pm
	Wow. Well, you can either use my drawings, or use the software which should give you considerably better results. With all the "cutlist plz" threads, why hasn't anyone said anything about that software...

Sinfinity Members Profile Send Private Message Find Members Posts Add to Buddy List Old Croc Joined: 06 July 2008 Status: Offline Points: 1632	Post Options Post Reply Quote Sinfinity Report Post Thanks(0) Quote Reply Posted: 14 October 2008 at 11:55pm
	Someone mentioned downloading software for cutlist on another thread, so i went for a hunt. Was easy to find, seems to work. However have not fully tested it so cant verify it does exactly what it says on the tin, however, fair amount of useful info on site before downloading. Wafflesound, see if it come up with same solution as your cutlist ?
	Matt at ukamp dot co dot uk

wafflesomd Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 21 September 2007 Status: Offline Points: 811	Post Options Post Reply Quote wafflesomd Report Post Thanks(0) Quote Reply Posted: 15 October 2008 at 12:06am
	I just used it and it's awesome. It will calculate the best possible solution to eliminate waste as well as other things. I only tried it with one 186. Gonna try four and see how close I came. "there are over 1,000,000,000 possible solutions, will now check the first million" I'm going to be here awhile. It finished. Turns out my cut list is better. I didn't take into account braces in either the software or my cutlist. In my plans cutlist, you would need 7 sheets, and end up with a whole half sheet 4x4' to make braces. With the software, it also had leftover scraps, but in smaller more spread out pieces. I'm still going to go off the software though. Some of the cuts in my cutlist would just be impossible. Edited by wafflesomd - 15 October 2008 at 12:43am