P-Audio E10-200a

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   This driver looks like it should work ok in the mt102 but I've never
built horns before! They're rated as 200wrms each with 100db
sensitivity and a BL of over 19,qts of .23 and fs of 77hz or so.

I'm in Australia so the recommended drivers are difficult to get my
hands on,these however are easy and seem to have good specs as well as
easily accessible recones.

The P series 10" 350rms driver says it has 100db sensitivity but seems
to hover around 90-93 for most of the range on their response graphs.At
the moment cannonsound have these drivers on fibreglass flares and
claim SPL is DEFINATELY NOT a problem! I'd rather the bigger beefier
drivers but if its a 10db loss in spl compared to the cheaper E
series,I'm not interested!

Is there anyone who knows the inputs for this horn in hornresp so I can check it out?

Thanks for your time 

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
LunchieTey Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 06 February 2005 Location: Australia Status: Offline Points: 934	Post Options Post Reply Quote LunchieTey Report Post Thanks(0) Quote Reply Topic: P-Audio E10-200a Posted: 09 November 2005 at 8:21am
	This driver looks like it should work ok in the mt102 but I've never built horns before! They're rated as 200wrms each with 100db sensitivity and a BL of over 19,qts of .23 and fs of 77hz or so. I'm in Australia so the recommended drivers are difficult to get my hands on,these however are easy and seem to have good specs as well as easily accessible recones. The P series 10" 350rms driver says it has 100db sensitivity but seems to hover around 90-93 for most of the range on their response graphs.At the moment cannonsound have these drivers on fibreglass flares and claim SPL is DEFINATELY NOT a problem! I'd rather the bigger beefier drivers but if its a 10db loss in spl compared to the cheaper E series,I'm not interested! Is there anyone who knows the inputs for this horn in hornresp so I can check it out? Thanks for your time
	Speaker addict

ceharden Members Profile Send Private Message Find Members Posts Add to Buddy List The 10,000 Points Club Joined: 05 June 2005 Location: Southampton Status: Offline Points: 11851	Post Options Post Reply Quote ceharden Report Post Thanks(0) Quote Reply Posted: 09 November 2005 at 8:49pm
	Have you considered the SN10MB? Parameters look good for horns although I haven't simulated yet. Should be easy to do a rough simulation for the MT102, just do it for one driver and half the flare. Only needs to be an exponential approximation to check the driver will work. Should be able to calculate throat and mouth area and read length off the plans.

LunchieTey Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 06 February 2005 Location: Australia Status: Offline Points: 934	Post Options Post Reply Quote LunchieTey Report Post Thanks(0) Quote Reply Posted: 11 November 2005 at 9:51pm
	Ok I went and modelled the tops using the p10-100mb and it produced a continuous average of 133db(135db in areas) and is pretty flat to 800hz 30deg off axis(2 drivers at 700wrms) Is this what people have been getting with this cab or is it low? I think I've got the inputs in Hornresp correct.
	Speaker addict

Timber_MG Members Profile Send Private Message Find Members Posts Add to Buddy List Registered User Joined: 27 March 2004 Location: South Africa Status: Offline Points: 1454	Post Options Post Reply Quote Timber_MG Report Post Thanks(0) Quote Reply Posted: 12 November 2005 at 2:54am
	Dont.fuss.about.te.output.round.te.botom.end..It.is.down.to. te.low.Q.in.a.direct.radiator.Sorry.Keyboard.is.broken

LunchieTey Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 06 February 2005 Location: Australia Status: Offline Points: 934	Post Options Post Reply Quote LunchieTey Report Post Thanks(0) Quote Reply Posted: 12 November 2005 at 11:39am
	Sweet. I've gone and ordered the drivers and will begin construction SOON! Thanks for the input
	Speaker addict

Mark James Members Profile Send Private Message Find Members Posts Add to Buddy List Old Croc Joined: 15 January 2006 Location: rig side Status: Offline Points: 5306	Post Options Post Reply Quote Mark James Report Post Thanks(0) Quote Reply Posted: 17 February 2006 at 8:38am
	has anyone ever heard a e10-200a in an mt102 [or more acurately has anyone heard a pair obviusly]

LunchieTey Members Profile Send Private Message Find Members Posts Add to Buddy List Young Croc Joined: 06 February 2005 Location: Australia Status: Offline Points: 934	Post Options Post Reply Quote LunchieTey Report Post Thanks(0) Quote Reply Posted: 10 March 2006 at 8:15pm
	Supply of the drivers was a problem at the time I started the topic and instead build dual 15" ported with 2" comps, plenty of output I must say so I'm not worried about the 102's anymore!
	Speaker addict