|
Alternative version of WSX (plan) |
Post Reply 
|
Page 12> |
| Author | |
Amano 
Registered User 
Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Alternative version of WSX (plan)Posted: 27 January 2010 at 7:54pm |
 |
|
 |
|
|
Amano
Registered User
Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 January 2010 at 7:59pm |
|
same horn path, same response... smaller.. easier
|
|
|
|
|
Quantum Sounds
Registered User
Joined: 26 December 2008 Status: Offline Points: 462 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 January 2010 at 8:51pm |
|
nice one anano
should have a better responce higher as the bends are kept around 90deg rather than 2 180's |
|
|
|
|
Saul
Old Croc 
Joined: 15 June 2007 Status: Offline Points: 5912 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 January 2010 at 9:45pm |
|
20mm difference between the two - was it worth the effort?
|
|
|
|
|
mykey
Old Croc
Joined: 18 August 2005 Location: UK/Indonesia Status: Offline Points: 9680 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 2:52am |
|
I like it
WSX made simple not simpler |
|
|
|
|
FlipC
Young Croc 
Joined: 25 October 2007 Status: Offline Points: 666 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 5:48am |
|
OK
Trying to get my head around this layout. So would the access hatch be from the front inside the mouth? With driver firing through the section that is 144mm? If so where would you personally run the wiring? I ask as that grey part which would be on what I think would be the access panel looks like a connector. |
|
|
|
|
Amano
Registered User
Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 6:45am |
That grey part is like http://www.audioroundtable.com/PiSpeakers/messages/17999.html
This is a Heat Exchanger.
Access hatch is at the front of..
144x378mm is an original WSX throat area.
|
|
|
|
|
Amano
Registered User
Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 6:53am |
yup, it was!
 this version hasn't parts having angles less than 45deg except for throat part... two ones
hatch is parallel to driver bottom to make heat exchanger
|
|
|
|
|
Amano
Registered User
Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 6:56am |
it shouldn't have big changes in response... maybe less distortion
|
|
|
|
|
_djk_
Old Croc
Joined: 23 November 2004 Location: United States Status: Offline Points: 5992 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 9:30am |
|
Looks like a good alternative to the often requested CV B36 types too.
|
|
|
djk
|
|
|
|
|
tomschute
Old Croc
Joined: 15 May 2006 Location: Mid Wales Status: Offline Points: 1817 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 9:56am |
|
Good effort - again
 @ FlipC easy, just run wiring straight through the centre panel through to the back panel @ Amano width...? Edited by tomschute - 28 January 2010 at 9:57am |
|
|
Out to lunch... stableaudio@hotmail.co.uk
www.stableaudio.co.uk Speaker Building Services |
|
|
|
|
Amano
Registered User
Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 January 2010 at 10:09am |
574mm as in original
|
|
|
|
|
Post Reply
|
Page 12> |
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
FlipC wrote: