Tweeter advice |
Post Reply | Page 12> |
Author | |
ollie3686
New Member Joined: 04 February 2019 Status: Offline Points: 9 |
Post Options
Thanks(0)
Posted: 07 February 2019 at 6:42am |
Definitely not carpeted. But there are chunks out of the wood, and one of the tweeters is missing. But dead cheap and the cones are still there
|
|
mini-mad
Old Croc Joined: 13 July 2012 Location: london Status: Offline Points: 6903 |
Post Options
Thanks(0)
|
the ones you've found, as long as they are not carpeted a lick of paint will see them like new and will sound better then any skytec
|
|
If it sounds like a gorilla is trying to escape, turn it down.
|
|
ollie3686
New Member Joined: 04 February 2019 Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Ok had a look on eBay/Facebook and can get some pretty cheap. Some which have been used for gigs and in terrible condition, but assuming the drivers are ok is there any mileage in simply replacing the skytecs? My cabinets are in really good condition
|
|
ollie3686
New Member Joined: 04 February 2019 Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Ok fair point
|
|
djscooby
Young Croc Joined: 15 March 2008 Location: United Kingdom Status: Offline Points: 1414 |
Post Options
Thanks(0)
|
Imho have a shop round on eBay you could get something better than skytec/qtx for less than £100 if it's only for you and your mates etc look at wharfedale Peavey etc
|
|
Well my wife has kicked me out saying it's over due to my obsession with speakers don't know watt I'm gonna do with no ohm to go to
|
|
concept-10
Young Croc Joined: 17 May 2016 Status: Offline Points: 1292 |
Post Options
Thanks(0)
|
Ok, when you replace the skyteks for something better you will not need what you are building.
|
|
ollie3686
New Member Joined: 04 February 2019 Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Thanks but I didn’t really want to touch the Skytecs, I was hoping to build something separate which I’ll still have when I replace the skytecs
|
|
concept-10
Young Croc Joined: 17 May 2016 Status: Offline Points: 1292 |
Post Options
Thanks(0)
|
All the components for Skytek are available on ebay and they are cheap, take your tweeter out and compare it, it's the easiest solution.
|
|
ollie3686
New Member Joined: 04 February 2019 Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Thanks mini-mad, sound like what I’m after. By shunt you mean a resistor right? (Apologies for the ignorance?)I get wiring the piezo’s jb parallel, but where do you add the shunt? Also does thos avoid the need for a crossover?
Edited by ollie3686 - 05 February 2019 at 8:02am |
|
mini-mad
Old Croc Joined: 13 July 2012 Location: london Status: Offline Points: 6903 |
Post Options
Thanks(0)
|
I would wire up 4x pizeos in parallel and stick a 10watt 8ohm shunt in series... the shunt will soften the harshness a little but will add a little sparkle and it's super cheap... it's not the best solution by any stretch but will at a little top end. I wouldn't "upgrade" them anymore then that as the investment would be like burning a £20 note. The advise would be just start saving and in the long run buy second hand branded speakers. Skytec is not worth the investment... so get about 8x pizeos (4x per box) and just try to soften the sound with a shunt or two. Don't go any further then that me old china
|
|
If it sounds like a gorilla is trying to escape, turn it down.
|
|
ollie3686
New Member Joined: 04 February 2019 Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Didn’t really want to touch them but instead build a separate tweeter box, or do you not think that’s worth doing either?
|
|
jammin75
Old Croc Joined: 08 July 2012 Location: west midlands Status: Offline Points: 2375 |
Post Options
Thanks(0)
|
not worth doin anything to them unless its bonfire nite u can pick up a used pair of monitors for not a lot of money
|
|
feel the vibes !!! "Who Feels it Knows it" Strong like Lion
|
|
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |