Powersoft PSU Driver Circuit |
Post Reply | Page 12> |
Author | ||
RobinMatrix
Young Croc Joined: 23 August 2013 Location: Kidderminster Status: Offline Points: 567 |
Post Options
Thanks(0)
Posted: 11 January 2020 at 2:38pm |
|
The problem is, the K10 version has different capacitor values to the QD series. The only way to get the capacitor values is to lift the components out and measure them.
|
||
Matrix Pro Audio ::http://matrixproaudio.com/"
|
||
mgee
Registered User Joined: 06 September 2019 Location: SOUTH AFRICA Status: Offline Points: 12 |
Post Options
Thanks(0)
|
|
send me your email at mgee626@gmail.com. ill send you clear picture of the board
|
||
mgee
Registered User Joined: 06 September 2019 Location: SOUTH AFRICA Status: Offline Points: 12 |
Post Options
Thanks(0)
|
|
ill send you photo of the driver soon Monday 13th
|
||
levyte357-
Old Croc Joined: 27 July 2012 Location: UK, South East Status: Offline Points: 8128 |
Post Options
Thanks(0)
|
|
Don't understand, buying Rolls Royce amp, but unwilling to send it to qualified engineers, to be fixed properly.
|
||
Global Depopulation - Alive and Killing.
|
||
dylan-penguinmedia
Old Croc Joined: 14 April 2011 Location: Brighton Status: Offline Points: 4575 |
Post Options
Thanks(0)
|
|
This is solid gold. Post of the year on 7/1! |
||
mk2_ginger_biscuit69
Old Croc Joined: 03 November 2008 Location: Brighton Status: Offline Points: 7801 |
Post Options
Thanks(0)
|
|
|
||
''Remember that the object of a subwoofer is to enhance the output of your main speakers, not overpower it''
''Dubstep - an elongated electronic fart'' |
||
mgee
Registered User Joined: 06 September 2019 Location: SOUTH AFRICA Status: Offline Points: 12 |
Post Options
Thanks(0)
|
|
Good day Sir
send your amp to me ill fix it. South Africa
|
||
RobinMatrix
Young Croc Joined: 23 August 2013 Location: Kidderminster Status: Offline Points: 567 |
Post Options
Thanks(0)
|
|
Note that although the crystal is much higher, (12.288MHz instead of 4.0MHz) the K10 uses a 4060 divider instead of the 4024 in the Q/D ... it picks up outputs Q6 and Q8 on the K10, but outputs Q4 and Q6 on the Q/D series ... so although the crystal is much higher, the end result pair of clock signals is actually slower ...
|
||
Matrix Pro Audio ::http://matrixproaudio.com/"
|
||
RobinMatrix
Young Croc Joined: 23 August 2013 Location: Kidderminster Status: Offline Points: 567 |
Post Options
Thanks(0)
|
|
If you need it repairing, I have extensive experience of this board ... if you want to send me a photo of the burnt parts, I should be able to assist. As a side note: there are 3 basic sections of this board, the rear most section is the clock gen and PFC driver, the centre section is the SMPS driver and the front section is the 15V v_aux generator ... if the fault is in either of the first two sections, I would look at the opto isolators located under the PSU heatsink, as the drive outputs from that card are normally opto-isolated, and if you have any burnt parts on the PSU card, then it is probable you also have a dead opto or two ... it's the three rearwards ones that drive the PFC and the two white front ones that drive the SMPS, you can forget the rest, they are PSU monitoring and control. |
||
Matrix Pro Audio ::http://matrixproaudio.com/"
|
||
Earplug
Old Croc Joined: 03 January 2012 Location: Europe Status: Offline Points: 7216 |
Post Options
Thanks(0)
|
|
Yes - but sometimes even that doesn´t guarantee schematics. I had a Behringer repair a while ago and managed to get hold of the main tech at the official repair place in Barcelona. He told me that even they weren´t given all the schematics - just relacement boards for most of the products. Anything else had to go back to the main office in Germany. |
||
Earplugs Are For Wimps!
|
||
simonp1100
Young Croc Joined: 01 September 2008 Location: Bristol Status: Offline Points: 1110 |
Post Options
Thanks(0)
|
|
The driver circuit as i can make out is nearly the same as the Q & D series PSU driver apart from a higher frequency oscillator at the front end & some major re-work on the FET Bootstrap driver circuit and of course now all surface mounted components. My problem is in this area mostly and because this part has changed a lot and some surface mount caps & resistors are burnt are unreadable, hence the circuit for this would cure the problem. The only other option is to copy the circuit from another board from a working amplifier & draw the circuit on my PCB CAD program (which is the easy part), but i don't know how long another Powersoft K10 will arrive at my repair bench with a working board in . Here's hoping for someone out there who has the circuit.
|
||
toastyghost
The 10,000 Points Club Joined: 09 January 2007 Location: Manchester Status: Offline Points: 10919 |
Post Options
Thanks(0)
|
|
Probably because even though they’re far from perfect, Real or their equivalent have the service contract? Considering how many utterly cowboy repair jobs I’ve seen on Powersoft power supplies, I understand why. You can also always send it to Powersoft HQ directly but you’ll have to be comfortable with the shipping time |
||
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |