Punisher Extension Development Thread |
Post Reply | Page <123 |
Author | |
Dutchman
Registered User Joined: 23 March 2013 Location: GENT Status: Offline Points: 365 |
Post Options
Thanks(0)
|
Awesome mate! Have a good one!
|
|
We need more SPL!
|
|
mobiele eenheid
Old Croc Joined: 15 August 2004 Location: Netherlands Status: Offline Points: 1568 |
Post Options
Thanks(0)
|
|
|
Phil B
Old Croc Joined: 21 November 2004 Location: Melbourne Status: Offline Points: 2328 |
Post Options
Thanks(0)
|
You could make that a flat pack with a bit of thought ? Our main issue was attaching the extension to the subs in the same place every time. Our subs are Top and bottom L+R with interlocking skids so they stay in the same position. We also always try to stack on the same pallets we carry.
The extensions all just clip on with the latches starting with the bottom panel then sides, top and braces last. Those latches have a screw adjustment so can be adjusted if things aren't totally level. Every joint edge of the extension panel has a wood batten with foam to make a rattle free fit Over the years we can now build them pretty quick, solve any rattles with a quick test track and pretty much forget after that ... I would like to add a horizontal brace at sometime but can't find any of that elusive time stuff kicking around ! AND they pack neatly into the trailer ... .p. Edited by Phil B - 29 November 2019 at 9:27am |
|
citizensc
Young Croc Joined: 16 October 2015 Location: Perth,Australia Status: Offline Points: 532 |
Post Options
Thanks(0)
|
Update:
I have made cut sheets and solidworks drawings for this, there are two versions, one to fit a double punisher mk2, and another, 15mm wider to fit 2 x single punisher mk2s. I have removed the strapping points from the drawing, going to leave it to the builders to design a method of attaching it to the punishers. I am not exactly experienced with autocad/solidworks and made these using trial versions of the software... I have done my best but would love suggestions for how to improve the drawings and make them more accessible so anyone can read and understand them. Here are the files - please check them before you build anything from them, just make sure the cut sheets match the drawing and the drawings are the right width to fit your punishers. For single punishers - https://www.dropbox.com/sh/cfpqqwb3dxnnj2n/AAClo4G6urnDpAq11a31me6Ca?dl=0 For double punishers - https://www.dropbox.com/sh/ekvinl4tdwd6259/AADSoeBMtZ7hu07iNRSpLmqTa?dl=0 PDF is for the double punisher version but you can apply most of it to the single punisher version just add 15mm to the width - https://www.dropbox.com/s/k56cocuhx4ym1aw/p-extension%20-%20double%20drawing.pdf?dl=0 Also does anyone know what software was used to generate this PDF? I would love mine to be that detailed and clear https://www.dropbox.com/s/djam4g1oqirwmsj/TH18%20Xoc1%20%2B%20CUT%20LIST.pdf?dl=0 If you have any feedback or questions please comment or message me! and feel free to make your own modifications to the design - I consider this open source. |
|
Elliot Thompson
Old Croc Joined: 02 April 2004 Location: United States Status: Offline Points: 5175 |
Post Options
Thanks(1)
|
It is good to read (yet I am not surprised)that you are pursuing this project. Based on your replies, it was obvious you wanted to create this project. You might want to consider making a new thread in the Punisher and X-tro forum so no one will be looking for the design 10 years from now and, can't find it in the General Forum. Best Regards,
|
|
Elliot Thompson
|
|
Post Reply | Page <123 |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |