Speakerplans.com Homepage
Forum Home Forum Home > Plans > Plan Requests
  New Posts New Posts RSS Feed - Martin Audio H3
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Martin Audio H3
 Post Reply Post Reply Page  <1234>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
dylan-penguinmedia View Drop Down
Old Croc
Old Croc
Avatar

Joined: 14 April 2011
Location: Brighton
Status: Offline
Points: 4575 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dylan-penguinmedia Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 3:36pm
Have a look for some W8’s if you’re going to go more than 1 a side on some WSX’s. 
Back to Top
lorenzo31071997 View Drop Down
Registered User
Registered User


Joined: 30 December 2019
Location: Italy
Status: Offline
Points: 18 		Post Options Post Options   Thanks (0) Thanks(0)   Quote lorenzo31071997 Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 4:09pm
Originally posted by dylan-penguinmedia dylan-penguinmedia wrote:

Have a look for some W8’s if you’re going to go more than 1 a side on some WSX’s. 

The W8 are not bad at all, but in Italy it is not found on second hand. I would prefer to build them, there is no mention of W8 anywhere on the web. As for the H3 / H3 + I already have how to configure the cuts, earnings etc.


Edited by lorenzo31071997 - 02 January 2020 at 4:17pm
Back to Top
smitske96 View Drop Down
Young Croc
Young Croc


Joined: 16 February 2016
Location: The Netherlands
Status: Offline
Points: 1092 		Post Options Post Options   Thanks (0) Thanks(0)   Quote smitske96 Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 5:20pm
Originally posted by lorenzo31071997 lorenzo31071997 wrote:

I had never heard of Peter Morris, I did a search on the web and I did not find a personal site where to find the design plans. I searched the forum and found several products, but not something done and finished. How difficult do you think the production of these boxes would be? We read that the configuration is very difficult to make them sound good, even if the yield is statospheric (how is it possible with only 2x12 "to make 100-20K Hz?). There are many plans of RCF 4PRO, specific components to use and the configurations are ready


If you searched correctly you would have found tons of information.

Including which drivers can be used, and also their correct processing. Nowhere is said that it is very hard to get them sounding right. If you want the best of the cab it will become more difficult because you need the correct FIR processing. 


PS: it doesn't only have two 12" drivers. The whole cab is mainly designed around the coax HF driver. You can use a 4" VC HF driver laike the RCF ND950 but you don't get the same result. If you go for the PM60 you can use two boxes aside (which would be loud).
Back to Top
Digbethdave View Drop Down
Registered User
Registered User
Avatar

Joined: 16 November 2018
Status: Offline
Points: 406 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Digbethdave Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 8:01pm
I guess your WSX are copies too? 
Back to Top
lorenzo31071997 View Drop Down
Registered User
Registered User


Joined: 30 December 2019
Location: Italy
Status: Offline
Points: 18 		Post Options Post Options   Thanks (0) Thanks(0)   Quote lorenzo31071997 Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 8:31pm
Originally posted by Digbethdave Digbethdave wrote:

I guess your WSX are copies too? 


Yes, the WSX are also copies. There are many design plans for the WSX. I had the boxes made by a specialized company that made many of them, the speakers are RCF 18LP300 that fit perfectly


Edited by lorenzo31071997 - 02 January 2020 at 8:32pm
Back to Top
Earplug View Drop Down
Old Croc
Old Croc


Joined: 03 January 2012
Location: Europe
Status: Offline
Points: 7216 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Earplug Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 8:47pm
If you're after some H3's, I have 4 here for sale. You can then open them up and copy to your heart's content.  Unhappy
Earplugs Are For Wimps!
Back to Top
lorenzo31071997 View Drop Down
Registered User
Registered User


Joined: 30 December 2019
Location: Italy
Status: Offline
Points: 18 		Post Options Post Options   Thanks (0) Thanks(0)   Quote lorenzo31071997 Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 8:53pm
Originally posted by Earplug Earplug wrote:

If you're after some H3's, I have 4 here for sale. You can then open them up and copy to your heart's content.  Unhappy

I'd pay for plans, but I'd like to build pits. Aren't you going to make plans?Big smile
Back to Top
dylan-penguinmedia View Drop Down
Old Croc
Old Croc
Avatar

Joined: 14 April 2011
Location: Brighton
Status: Offline
Points: 4575 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dylan-penguinmedia Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 9:35pm
Not sure which part of “nobody here’s gonna give you commercial plans, it’s frowned upon and a bit shit” you’re not getting.
Back to Top
mk2_ginger_biscuit69 View Drop Down
Old Croc
Old Croc


Joined: 03 November 2008
Location: Brighton
Status: Offline
Points: 7801 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mk2_ginger_biscuit69 Quote  Post ReplyReply Direct Link To This Post Posted: 02 January 2020 at 11:31pm
here you go, this is a great start to reverse engineer. You need to get a 15" 10" & 1" driver in there, and make it weigh 77.5kg. Should be easy to do!
''Remember that the object of a subwoofer is to enhance the output of your main speakers, not overpower it''

''Dubstep - an elongated electronic fart''
Back to Top
lorenzo31071997 View Drop Down
Registered User
Registered User


Joined: 30 December 2019
Location: Italy
Status: Offline
Points: 18 		Post Options Post Options   Thanks (0) Thanks(0)   Quote lorenzo31071997 Quote  Post ReplyReply Direct Link To This Post Posted: 03 January 2020 at 12:07am
Originally posted by mk2_ginger_biscuit69 mk2_ginger_biscuit69 wrote:

here you go, this is a great start to reverse engineer. You need to get a 15" 10" & 1" driver in there, and make it weigh 77.5kg. Should be easy to do!



I already had these data, did you want to make a joke?LOL
Back to Top
Danny A View Drop Down
Registered User
Registered User
Avatar

Joined: 30 May 2009
Status: Offline
Points: 444 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Danny A Quote  Post ReplyReply Direct Link To This Post Posted: 03 January 2020 at 1:22am
deleted



Edited by Danny A - 03 January 2020 at 1:22am
Back to Top
djeddie View Drop Down
Old Croc
Old Croc
Avatar

Joined: 26 April 2004
Location: Bristol
Status: Offline
Points: 4125 		Post Options Post Options   Thanks (0) Thanks(0)   Quote djeddie Quote  Post ReplyReply Direct Link To This Post Posted: 03 January 2020 at 9:31am
Whilst it won't get you the H3, but here's a link to find the Peter Morris designs... either the 60 or 90 degree.


Also, why not have a search for the X-TRO?
Chas n Dave : it's like Drum and Bass but with beards.             E=mc² ±3dB
Back to Top
 Post Reply Post Reply Page  <1234>

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2023 Web Wiz Ltd.

This page was generated in 0.094 seconds.