Contact cleaner recipe? |
Post Reply |
Author | |
studio45
Old Croc Joined: 16 October 2007 Location: United Kingdom Status: Offline Points: 3864 |
Post Options
Thanks(0)
Posted: 28 January 2020 at 3:12pm |
Been Googling about trying to work out what is in Deoxit in an attempt to not have to pay £25 per small can of the damned stuff. Got as far as working out that it must contain oleic acid as the de-oxidising agent and that the main solvent is naptha, aka Coleman stove fuel.
Anyone got an idea of what else might be in there? A light oil like 3-in-1 perhaps, to remain as a lubricant after the naptha evaporates? I'm worried the oleic is going to hang around after doing its work, and maybe cause corrosion, or just get sticky and attract dust. Maybe Deoxit solved that issue and that's why it is so expensive? Or is it just a case of not putting too much it? A 5% by volume solution certainly cleans up copper pennies a treat, and that's really not very much...
|
|
Studio45 - Repairs & Building Commotion Soundsystem -Mobile PA
|
|
ceharden
The 10,000 Points Club Joined: 05 June 2005 Location: Southampton Status: Offline Points: 11776 |
Post Options
Thanks(0)
|
Electrolube EML200 is cheaper and I find it quite effective in many situations. However just squirting contact cleaner/lubricant into potentiometers is only ever a temporary fix/partial solution. If you can disassemble them and clean the tracks/contacts with some EML200 on a cotton bud then you get very good results. Works especially well on more expensive crossfaders etc. Alongside a little light oil on the mechanical slides.
Don't use ordinary oil on electrical contacts, it's an insulator! |
|
mk2_ginger_biscuit69
Old Croc Joined: 03 November 2008 Location: Brighton Status: Offline Points: 7801 |
Post Options
Thanks(0)
|
i can confirm that used engine oil is also a superb insulator. After a split hose covered the van engine, nearly every electric contact needed removing and cleaning, just need a steam cleaner to sort out the rest! |
|
''Remember that the object of a subwoofer is to enhance the output of your main speakers, not overpower it''
''Dubstep - an elongated electronic fart'' |
|
Meat
Old Croc Joined: 05 June 2009 Location: Manc Status: Offline Points: 1514 |
Post Options
Thanks(0)
|
You sure about the oleic acid? That should just stick to metal oxides. It's a very standard stabiliser for oxides in nanotechnology (many ferrofluids use this). I don't think that's gonna work. Looking at the MSDS I see Pentafluoropropane and isobutanol with a proprietry deoxidising agent. Both of these are very good penetrating solvents with not too low boiling points which should be a nice carrier to do the bit with the magic stuff. That's the key; low surface tension carrier with highish boiling point and good ability to solubilise whatever crud gets made. Good luck and try not to blow yourself up trying reverse egg-gin-earing. ;)
|
|
Don't test the champignon sound
|
|
Wikl109
Young Croc Joined: 29 April 2009 Location: Yorkshire Status: Offline Points: 969 |
Post Options
Thanks(0)
|
I use Electrolube now. It is one of the products that will work on both pots & faders. I recently had to gut an ex-install A&H Xone mixer that had been filled with Coca-Cola. The owner said the X-fader was beyond help, but after several hours dismantling, Fairy-Liquid flushing, then treating with Electrolube, it now works perfectly.
Edited by Wikl109 - 28 January 2020 at 10:45pm |
|
Cheers, Chris.
|
|
studio45
Old Croc Joined: 16 October 2007 Location: United Kingdom Status: Offline Points: 3864 |
Post Options
Thanks(0)
|
I'm guessing the oleic attacks the metal and dissolves the surface so the oxide falls off? Which is a bit scary but we're only talking a few atoms I hope! Only tried it on copper coins so far, but it certainly gets them bright and shiny quite quickly. Lifts the oxide right off, which forms a green scum layer over the oleic solution. Perhaps it'd be a case of applying my dreadful nostrum, waiting a day and then flushing out with pure solvent, followed by a light oiling. I will give it a try and report back.... |
|
Studio45 - Repairs & Building Commotion Soundsystem -Mobile PA
|
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |