Speakerplans.com Homepage
Forum Home Forum Home > General > Newbie Discussion
  New Posts New Posts RSS Feed - Guide to WinISD Pro and Hornresp
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Guide to WinISD Pro and Hornresp

 Post Reply Post Reply Page  <1 34567 12>
Author
Message Reverse Sort Order
Centauri View Drop Down
Old Croc
Old Croc


Joined: 29 November 2004
Location: Newcastle Aus
Status: Offline
Points: 1792
Post Options Post Options   Thanks (0) Thanks(0)   Quote Centauri Quote  Post ReplyReply Direct Link To This Post Posted: 07 February 2012 at 7:04am
If you had a look at the link I posted further up this page, it directs you to the current site at  http://www.hornresp.net.ms/
Back to Top
brooa View Drop Down
Registered User
Registered User
Avatar

Joined: 23 August 2011
Location: Australia
Status: Offline
Points: 162
Post Options Post Options   Thanks (0) Thanks(0)   Quote brooa Quote  Post ReplyReply Direct Link To This Post Posted: 07 February 2012 at 6:17am
hey guys cant seem to find a working download anywhere for hornresp, can someone link me to one?

thanks :)


Edited by brooa - 07 February 2012 at 6:32am
Back to Top
tkollen View Drop Down
New Member
New Member


Joined: 03 February 2012
Location: Great Falls, VA
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote tkollen Quote  Post ReplyReply Direct Link To This Post Posted: 03 February 2012 at 11:44pm
Can anyone advise me on the following:

I am trying to simulate a horn tweeter using Hornresp.  The driver I am using is very unconventional - It is a small modulated corona plasma flame coming from a tungsten rod tip. You could say that the diafragm is completely without mass. I intend to insert this tip into the throat of a ceramic horn.  The lower cut off frequency without horn is ca. 5000 Hz. I want to lower this frequency to ca. 2000 Hz.

Is Hornresp suitable for this task and if so I am looking for some guidance on what parameters to use, or is there a better simulator out there for this task?

Anyone please?
Back to Top
HighGradeBlazer View Drop Down
Registered User
Registered User


Joined: 12 December 2011
Status: Offline
Points: 10
Post Options Post Options   Thanks (0) Thanks(0)   Quote HighGradeBlazer Quote  Post ReplyReply Direct Link To This Post Posted: 17 December 2011 at 6:17pm
Very helpful...thanks :)
Back to Top
mobiele eenheid View Drop Down
Old Croc
Old Croc


Joined: 15 August 2004
Location: Netherlands
Status: Offline
Points: 1568
Post Options Post Options   Thanks (0) Thanks(0)   Quote mobiele eenheid Quote  Post ReplyReply Direct Link To This Post Posted: 10 September 2010 at 3:10pm

Two times the PD186 in the G-sub should be close to 100 dB/W/m. Other drivers might give less or better results. WinISD Pro is a bit pessimistic about band pass enclosures, you could simulate using Hornresp.

 
Regards Johan
Back to Top
Fiore_89 View Drop Down
Registered User
Registered User


Joined: 09 July 2009
Status: Offline
Points: 33
Post Options Post Options   Thanks (0) Thanks(0)   Quote Fiore_89 Quote  Post ReplyReply Direct Link To This Post Posted: 10 September 2010 at 12:54am
Hi, thanks for this complete guide to winISD but i don't understand a thing... 
If I simulate one of reflex or bandpass plans as Gsub or X1 the SPL response graphics in WinISD  show me a line always about 3dB less than original SPL response graphics reported on the plans paper of Rog, why?
 
I'm new and my question would be trivial but pleese reply me!
thanks
Back to Top
teslaman View Drop Down
Registered User
Registered User
Avatar

Joined: 11 June 2009
Location: Huntingdon
Status: Offline
Points: 302
Post Options Post Options   Thanks (0) Thanks(0)   Quote teslaman Quote  Post ReplyReply Direct Link To This Post Posted: 10 June 2010 at 11:29am
Brilliant, many thanks!
Back to Top
Centauri View Drop Down
Old Croc
Old Croc


Joined: 29 November 2004
Location: Newcastle Aus
Status: Offline
Points: 1792
Post Options Post Options   Thanks (0) Thanks(0)   Quote Centauri Quote  Post ReplyReply Direct Link To This Post Posted: 10 June 2010 at 9:25am
Now at http://www.dmcbean.bigblog.com.au/index.do
Back to Top
teslaman View Drop Down
Registered User
Registered User
Avatar

Joined: 11 June 2009
Location: Huntingdon
Status: Offline
Points: 302
Post Options Post Options   Thanks (0) Thanks(0)   Quote teslaman Quote  Post ReplyReply Direct Link To This Post Posted: 10 June 2010 at 9:20am
Has the Hornresp page moved? I was looking to download and google suggests http://mywebsite.bigpond.com/dmcbean/ is the place to go but I just get the following error:

HTTP Server Error 503

No available server to handle this request

Anyone know where I can download from?

Cheers.

Back to Top
mobiele eenheid View Drop Down
Old Croc
Old Croc


Joined: 15 August 2004
Location: Netherlands
Status: Offline
Points: 1568
Post Options Post Options   Thanks (0) Thanks(0)   Quote mobiele eenheid Quote  Post ReplyReply Direct Link To This Post Posted: 04 June 2010 at 1:56pm
2 pi
 
Regards Johan
Back to Top
airbell View Drop Down
Registered User
Registered User


Joined: 11 June 2009
Location: Berlin, Germany
Status: Offline
Points: 284
Post Options Post Options   Thanks (0) Thanks(0)   Quote airbell Quote  Post ReplyReply Direct Link To This Post Posted: 04 June 2010 at 12:45pm
short question: are the graphs in WINISD in halfspace (2pi) or full space (4pi)???
thanks
Back to Top
mobiele eenheid View Drop Down
Old Croc
Old Croc


Joined: 15 August 2004
Location: Netherlands
Status: Offline
Points: 1568
Post Options Post Options   Thanks (0) Thanks(0)   Quote mobiele eenheid Quote  Post ReplyReply Direct Link To This Post Posted: 17 April 2010 at 11:40pm
Now it is, thanks for the note.
 
Best regards Johan
 
Back to Top
 Post Reply Post Reply Page  <1 34567 12>

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2023 Web Wiz Ltd.

This page was generated in 0.094 seconds.