2x18" MEATGRINDER v2 (done!) |
Post Reply | Page <1 1112131415 22> |
Author | |
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
loudspeakerguru (Jeff Robinson): Edited by Amano - 14 September 2009 at 3:23pm |
|
bitzo
Registered User Joined: 20 November 2007 Location: Italy Status: Offline Points: 977 |
Post Options
Thanks(0)
|
I see....many thanks! so if you flip on a side the cab this phantom part will change...am I right?
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
Hmmm... I don't really know about 0.5-2xPi... But i think it can change in 4xPi |
|
bitzo
Registered User Joined: 20 November 2007 Location: Italy Status: Offline Points: 977 |
Post Options
Thanks(0)
|
So the the same concept can be applied to hog scoop sim even if it's a tapped horn...or not?
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
v3 dims:
1200x1066x600mm v2 is deeper than v3 in 134mm
Edited by Amano - 14 September 2009 at 3:38pm |
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
This concept can be applied to any horns i think! Measure real and total horn length 1850, WSX... and others and You'll understand it!
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
done measurements for MG218 v2!!!
single cab, outdoors, vertical standing, 1meter, 2 volts, Log sine Sweep not equalized plot: equalized plot: now it's time to drink beer...
Edited by Amano - 19 September 2009 at 5:30pm |
|
Cyklist
Young Croc Joined: 14 December 2007 Location: Ireland Status: Offline Points: 707 |
Post Options
Thanks(0)
|
wow, nice plot,
what are recommended drivers for the meatgrinder v3? |
|
purple monkey dishwasher
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
2x18nlw9600 for v2 and v3!!!
But I measured it (!!!V2!!!) with 2xc18-600lf
Edited by Amano - 19 September 2009 at 5:00pm |
|
levyte357
The 10,000 Points Club Joined: 10 May 2004 Location: UK, London Status: Offline Points: 11743 |
Post Options
Thanks(0)
|
Excellent news Amano. What was the Eq applied? |
|
"Who am I? I'm the guy who does his job.. You must be the other guy".
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
what do you mean? what device i used or how i adjust it?
|
|
Amano
Registered User Joined: 06 October 2008 Location: Russia Status: Offline Points: 219 |
Post Options
Thanks(0)
|
now I want to do v3 because its design I like much better
|
|
Post Reply | Page <1 1112131415 22> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |