outline t6.5 /powersoft digam7000 service manual |
Post Reply | Page <1234 7> |
Author | |
noobsound
Registered User Joined: 28 March 2008 Location: Romania Status: Offline Points: 67 |
Post Options
Thanks(0)
|
Hello. The amplifier is now repaired and runs like new. A friend of mine gave me the number of the guy who was in charge of repairing outline amps in Romania. The amp did not have anything burned in it , it was just some corosion problems on some part due to the fact that somebody managed to spill some cofee or juice in it.
Me and the user Adircf tested the amp a few hours back it it works fine.
|
|
Melaineamp
New Member Joined: 05 November 2008 Status: Offline Points: 3 |
Post Options
Thanks(0)
|
can send to melianeamp@gmail.com ? I meet a problem on t11.
|
|
noobsound
Registered User Joined: 28 March 2008 Location: Romania Status: Offline Points: 67 |
Post Options
Thanks(0)
|
@ melaineamp u want the schematics of the power suply?
|
|
Melaineamp
New Member Joined: 05 November 2008 Status: Offline Points: 3 |
Post Options
Thanks(0)
|
@ noobsound I want the schematics of amplification. thanks
|
|
soundgodz
New Member Joined: 14 April 2010 Location: Portland oregon Status: Offline Points: 2 |
Post Options
Thanks(0)
|
Hey noodsound can i get the Digam 7000 schematics? Thanks kwruecker@qwest.net |
|
Bryan M
Old Croc Joined: 17 July 2004 Location: England/Belgium Status: Offline Points: 2223 |
Post Options
Thanks(0)
|
Do all you guy genuinely have problems with your powersofts or do you just want to copy the design?
|
|
soundgodz
New Member Joined: 14 April 2010 Location: Portland oregon Status: Offline Points: 2 |
Post Options
Thanks(0)
|
Bryan Yes I have a problem with the input level.' works fine and then will go full blast like the ground is coming off on the level pot. I opened and found the ribbon that connects the front panel has a broken header. I also saw a pile of dust bridging th legs of the level pot. the input circuit board was covered with a fine grit i cleaned all and will test again. have found this to be a reliable and it still works despite this problem. I still have not recieved the service manual from anyone yet. |
|
serhatkay
New Member Joined: 12 May 2010 Location: Turkiye Status: Offline Points: 1 |
Post Options
Thanks(0)
|
hello Basil can you send "digam 7000 service manual" to me
thank you very much
best regards
Serhat Kaya
ProAudio/Electronic Technician - Turkiye
|
|
abeltronics
Registered User Joined: 16 July 2009 Location: Norwich Status: Offline Points: 265 |
Post Options
Thanks(0)
|
http://www.abeltronics.co.uk - Electronic Engineers
|
|
rona1977
New Member Joined: 18 May 2010 Status: Offline Points: 1 |
Post Options
Thanks(0)
|
Hi! Can you send the diagram to me too?
rona1977@libero.it |
|
Oldmaelstrom
Registered User Joined: 07 October 2009 Status: Offline Points: 15 |
Post Options
Thanks(0)
|
and me please switchlab@gmail.com
Thanks |
|
soc15
New Member Joined: 08 July 2010 Status: Offline Points: 1 |
Post Options
Thanks(0)
|
Me too please... For powersoft digam7000 service manual somcha.P@gmail.com |
|
Post Reply | Page <1234 7> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |