Actually Building a PC |
Post Reply | Page <1234 5> |
Author | |
joshd963
Registered User Joined: 09 September 2009 Status: Offline Points: 375 |
Post Options
Thanks(0)
|
|
|
b3n
Registered User Joined: 28 September 2008 Location: Brighton, UK Status: Offline Points: 222 |
Post Options
Thanks(0)
|
I dont think I have ever used an anti-static wristband in years of building PC's
Might explain why I have had parts die on me though! |
|
Matrix XP3000H, Thomann TA1050, Peavey CS1400, QSC RMX1450
2 x Eminence Kappa and PSD2002 loaded x15's 2 x SN-15MB and BM-D450 loaded X15's 2 x V18-1000 loaded 1850's Behringer DCX2496 |
|
odc04r
Old Croc Joined: 12 July 2006 Location: Sarfampton Status: Offline Points: 5483 |
Post Options
Thanks(0)
|
I just touch a grounded point (radiator pipe etc) before I start and don't build them in carpet covered rooms
|
|
Admin
Admin Group Forum Administrator Joined: 01 October 2003 Status: Offline Points: 1675 |
Post Options
Thanks(0)
|
I do have anti static wrist bands in my tool kit, but never use them.
I do the same as odc04r stay away from carpets and sometimes if I remember touch a grounding point. Considering I am often taking apart £5,000 plus servers I really should start wearing one. Edited by bruce - 14 January 2010 at 5:30pm |
|
norty303
Old Croc Joined: 18 August 2004 Location: Eastbourne Status: Offline Points: 8806 |
Post Options
Thanks(0)
|
Same here, never used an antistatic band.
I normally install the PSU first, and then plug it into the power socket but turned off. You now have the case grounded. I just make sure I touch the case periodically whilst working, but as you're normally rooting round inside anyway, it's fairly hard not to ground yourself. I've never killed a component so it must work.... |
|
My laser stuff: Frikkin Lasers
|
|
bassmish
Young Croc Joined: 28 October 2007 Location: MAAAANCHESTER Status: Offline Points: 1333 |
Post Options
Thanks(0)
|
that's what I would have done norty
got me a wristband today tho, to be on the safeside. although I can'T SAY i really understand how it's gonna be any help... I wish the postman would hurry up and bring me the rest of my dubmachine! |
|
Calculus
Young Croc Joined: 03 January 2005 Location: Newcastle Uk Status: Offline Points: 1105 |
Post Options
Thanks(0)
|
do you not need heat sink compound when fitting the fan to the processor???
|
|
joshd963
Registered User Joined: 09 September 2009 Status: Offline Points: 375 |
Post Options
Thanks(0)
|
|
|
odc04r
Old Croc Joined: 12 July 2006 Location: Sarfampton Status: Offline Points: 5483 |
Post Options
Thanks(0)
|
Most coolers will come with a heat compound pad preapplied. Performance is not usually as good compared to if you were to remove it (scrape it off + acetone) and reapply a smaller amount of higher quality paste I find. Certainly does work though.
|
|
Calculus
Young Croc Joined: 03 January 2005 Location: Newcastle Uk Status: Offline Points: 1105 |
Post Options
Thanks(0)
|
cool just wondered.. the white stuff is apparently a silver oxide paste.... I reset the prossessor in my laptop with some and cleaned the fan best thing i ever did with the laptop after two n half years it was full o dust...made it run like new again.
|
|
Calculus
Young Croc Joined: 03 January 2005 Location: Newcastle Uk Status: Offline Points: 1105 |
Post Options
Thanks(0)
|
same stuff between chips on amps and the main heatsink if you ever wondered what the white gloop is.
|
|
bassmish
Young Croc Joined: 28 October 2007 Location: MAAAANCHESTER Status: Offline Points: 1333 |
Post Options
Thanks(0)
|
aargh!
I just got my mother board and precessor, so I'm gonna start uilding right away! BUT.. I have no keyboard!! bugger |
|
Post Reply | Page <1234 5> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |