MT121 vs MT130 |
Post Reply | Page 123> |
Author | |
4four
New Member Joined: 30 August 2020 Status: Offline Points: 1 |
Post Options
Thanks(0)
Posted: 30 August 2020 at 12:29am |
Do you have pictures of the MT 130 project with the 15 "reflex? The efficiency after the 15" reflex that was inserted in the project is ready? |
|
dlyxover
Old Croc Joined: 14 June 2007 Location: Liverpool Status: Offline Points: 1508 |
Post Options
Thanks(0)
|
I've been working on a 10" cab similar to above, will put some sketchup screen shots up when I get a chance
|
|
In the Truth there is no news, and in the News there is no truth
|
|
geoSal
Registered User Joined: 05 July 2011 Location: THESSALONIKI Status: Offline Points: 338 |
Post Options
Thanks(0)
|
geoSal
Registered User Joined: 05 July 2011 Location: THESSALONIKI Status: Offline Points: 338 |
Post Options
Thanks(0)
|
anyone thought of designing mt130 with 10'' drivers?
i was planning to give it a try.drivers are 18 sound 10m600. please share your thoughts about it.. my aim is 180-1.2khz. mt122 style of cab. my experience with hornspec is not so big so any help would be nice thanks |
|
midas
Old Croc Joined: 27 October 2011 Location: Cumbria Status: Offline Points: 2117 |
Post Options
Thanks(0)
|
I have a pair of Yamaha S215IV's and am thinking of doing something similar to those.
I have a pair of PAudio ES600 15's need to check if they would be ok at the bottom. Just need something not to expensive for the mids and top. If the 2 inch would not sound so good.
|
|
t.geessounds
Young Croc Joined: 10 May 2010 Location: US... New york Status: Offline Points: 908 |
Post Options
Thanks(0)
|
Nice Box DiscernAudio
|
|
DiscernAudio
Young Croc Joined: 08 June 2011 Location: Alabama Status: Offline Points: 541 |
Post Options
Thanks(0)
|
Not my build, nor my speaker, I was just tasked to design the 15" reflex on the bottom.
It is what the customer wanted. What do you think? Edited by DiscernAudio - 05 June 2013 at 3:18pm |
|
MarjanM
Old Croc Joined: 10 February 2005 Location: Macedonia Status: Offline Points: 7810 |
Post Options
Thanks(0)
|
Kevin, please do report on those 12N810. I am also planing some box with those. On paper they look extremely good.
|
|
Marjan Milosevic
MM-Acoustics www.mm-acoustics.com https://www.facebook.com/pages/MM-Acoustics/608901282527713 |
|
kevinmcdonough
Old Croc Joined: 27 June 2005 Location: Glasgow Status: Offline Points: 3749 |
Post Options
Thanks(0)
|
hey
both are hornloaded mids and both add a good chunk of sensitivity to whatever 12" you use. The MT-130 reportedly goes slightly lower, and it a little bit flatter. They will have a slightly different sound with the 130 being a slot throat, and people describe the fact that the seem to give the impression of being VERY "long throw" to the point of almost sounding weird up close. Once I get my current build out the way i plan to make up some mock ups of the 12" section over the summer and try it out, both with a BMS 12N810 (have two for testing already had this in the back of my head for a while) and an either an eighteensound mb600 or mb1000 (which i'll have to get) and see what they sound like. Long term plan is to make two tops a side that are double 12" high sensitivity drivers (much like above) with the big coax BMS compression driver, and have a go at a double 15" bifurcated ported horn and make three of them a side to sit under. The main problem is that while loads of people have built MT-122s or MT112s, there seems to be very few that have built 130s and no one that I know that has both, so there hasn't really been a huge amount of feedback on them or any chance to properly compare the two. k Edited by kevinmcdonough - 15 May 2012 at 7:27am |
|
jwdrain
Young Croc Joined: 01 December 2011 Location: Sheffield Status: Offline Points: 585 |
Post Options
Thanks(0)
|
what are the differences between MT121s and MT130s? Just the throw?
|
|
Absulum
Registered User Joined: 01 February 2012 Location: Sheffield Status: Offline Points: 267 |
Post Options
Thanks(0)
|
How much does the rear chamber size matter with a box like this? Thinking of making two of these without the HF horn section. By no means a master carpenter, and would like to make the box square rather than trap, which would result in a larger rear chamber (and less mitre joints).
There is also mention of this being long throw - will it sound ok in smaller venues too? Thanks :)
|
|
jerronimo
Registered User Joined: 11 July 2009 Location: Nederland Status: Offline Points: 438 |
Post Options
Thanks(0)
|
Yes that should make plenty of noise!
Still not decided about the mid drivers, it's going to be the B&C or the Beyma. The b&c is a bit more efficient but the beyma has higher powerhandling and xmax, and therefore should be able to be crossed a little lower without hitting the xmax. I'm planning to build: 4x mt-130 loaded with b&c or beyma and BMS 4550 comp. driver 4x MHB-46 loaded with rcf lf18n401 or lf18g401 or maybe the void V-1000 So I can use 1 mhb-46 and mt130 a side for small events and 2 of both a side for larger events. Or 4x mhb-46 centre stacked when space is available. Keep us updated with your buildprogress, allways nice to see other people's efforts. |
|
Post Reply | Page 123> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |