Broken C-Audio Amplifiers Wanted. |
Post Reply | Page 12> |
Author | |
technoman
Registered User Joined: 23 May 2011 Location: Somerset Status: Offline Points: 127 |
Post Options
Thanks(0)
Posted: 10 June 2011 at 8:36pm |
Looking for the following C-Audio Amplifiers BROKEN ONLY for spares inventory, anything considered & cash waiting.
RA Series (RA1001, 2001, 3001, & RA4001's). XR3801's & XR5001's. SRX series. Please PM me. Regards |
|
wires
Young Croc Joined: 21 May 2009 Status: Offline Points: 1365 |
Post Options
Thanks(0)
|
I have a xr5001, one channel in protect. Not really 'broken' i just haven't got round to sorting it out still.
Let me know what you have in mind.
|
|
technoman
Registered User Joined: 23 May 2011 Location: Somerset Status: Offline Points: 127 |
Post Options
Thanks(0)
|
How much were you thinking of (bear in mind that it will be used as spares inventory) ???.
|
|
dubclot
Registered User Joined: 26 May 2010 Location: London Status: Offline Points: 373 |
Post Options
Thanks(0)
|
Got a GB202 if of any interest?
|
|
wires
Young Croc Joined: 21 May 2009 Status: Offline Points: 1365 |
Post Options
Thanks(0)
|
Ah ok, it's not in that bad a condition so wouldn't really class it 'just for spares' if you know what i mean.
If you're still interested drop me an offer, i'm selling it anyway even when i get round to fixing it as i'm slowly upgrading all my amps. Cheers.
|
|
technoman
Registered User Joined: 23 May 2011 Location: Somerset Status: Offline Points: 127 |
Post Options
Thanks(0)
|
All depends on price. What did you have in mind ????? |
|
dubclot
Registered User Joined: 26 May 2010 Location: London Status: Offline Points: 373 |
Post Options
Thanks(0)
|
Anything really. Would I have to post?
|
|
technoman
Registered User Joined: 23 May 2011 Location: Somerset Status: Offline Points: 127 |
Post Options
Thanks(0)
|
yes you would have to post as i am based in somerset. What is the base starting price ?????.
|
|
trappert
Registered User Joined: 06 October 2008 Status: Offline Points: 96 |
Post Options
Thanks(0)
|
We've got Pulses, 2 channel and 4 channel.
|
|
technoman
Registered User Joined: 23 May 2011 Location: Somerset Status: Offline Points: 127 |
Post Options
Thanks(0)
|
What are they, how many & what price are you looking for them ?????.
|
|
trappert
Registered User Joined: 06 October 2008 Status: Offline Points: 96 |
Post Options
Thanks(0)
|
Hi,
We have 3 x Pulse 2x1100 all with PSU fault. I have copied the specs below. £120 for the lot plus postage?
PULSE 4x300 Measured per channel, both channels driven at 1khz to no more than 0.1% THD+N 8 Ohms 170Wrms 4 Ohms 300Wrms 2 Ohms 330Wrms* *Note: 2 Ohm spec is at 1% THD 16 Ohm 400Wrms 8 Ohm 600Wrms 4 Ohm 660Wrms* *Note: 4 Ohm bridged spec is at 1% THD Input Imp. 20kOhm Distortion <0.006% THD, 1kHz, 1dB below clip, 22kHz measurement bandwidth Frq. Response 20Hz to 20kHz, +0/0.2dB; <2Hz to >120Hz +0/-3dB Controls Power switch, bridge mode switching, indented level controls(these may be made tamper-proof) Indicators Mains present, Operate, Signal, Bridge, Clip, Protect, Remote Protection Microprocessor supervised: Over-temperature, DC on outputs, output stage overload, Inrush current surge, mains fail and blownout.
Noise <100dB ref full output 20Hz – 20kHz measurement bandwidth Slew Rate >50 V/microsecond Damping factor >200 ref 8 Ohm Output Connectors 4x300 – Binding post or speakon 2x650, 2x1100 – Binding post and Speakon Power 115 or 230 volts AC nominal, internally selectable, 2000VA, all channels driven
(4x300, 2x650); 3000VA (2x100) Dimensions 3.5” (89mm) x 18.2” (460mm) x 19” (483mm) with rear rack ears depth 19.5 “,
21”, 20” (494, 511, 530mm) Weight 24lb (11kg) PULSE 2x1100
Power Ratings Measured per channel, both channels driven at 1khz to no more than 0.1% THD+N 8 Ohms 700Wrms 4 Ohms 1100Wrms 2 Ohms 1500Wrms* *Note: 2 Ohm spec is at 1% THD Bridged Mono 16 Ohm 1200Wrms 8 Ohm 2200Wrms 4 Ohm 3000Wrms* *Note: 4 Ohm bridged spec is at 1% THD Input Sensitivity +1dBu for full output Input Imp. 20kOhm Distortion <0.008% THD, 1kHz, 1dB below clip, 22kHz measurement bandwidth Frq. Response 20Hz to 20kHz, +0/0.2dB; <2Hz to >120Hz +0/-3dB Controls Power switch, bridge mode switching, indented level controls (these may be made tamper-proof) Indicators Mains present, Operate, Signal, Bridge, Clip, Protect, Remote Protection Microprocessor supervised: Over-temperature, DC on outputs, output stage overload, Inrush current surge, mains fail and blownout. Noise <100dB ref full output 20Hz – 20kHz measurement bandwidth Slew Rate >50 V/microsecond Damping factor >200 ref 8 Ohm Output Connectors Binding post and Speakon Power 115 or 230 volts AC nominal, internally selectable, 2000VA, all channels driven Dimensions 3.5” (89mm) x 18.2” (460mm) x 19” (483mm) with rear rack ears depth 19.5 “, 21”, 20” (494, 511, 530mm) Weight 24lb (11kg) |
|
technoman
Registered User Joined: 23 May 2011 Location: Somerset Status: Offline Points: 127 |
Post Options
Thanks(0)
|
Have PM you. Regards
|
|
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |