Dual driver subs impedance |
Post Reply | Page 12> |
Author | |
TomD
Registered User Joined: 22 July 2006 Status: Offline Points: 6 |
Post Options
Thanks(0)
Posted: 22 July 2006 at 2:03pm |
Hi
If I want to build some 2x15" subs, and want the completed cabinet to end up at 8 ohms, what's the best way of going about this? I could either use 2 4ohm drivers in series, or 2 16ohm paralleled. If, as an example, each driver was 1000w, what would the total rated power of the cabinet be in each case? |
|
JD01
Young Croc Joined: 23 August 2004 Status: Offline Points: 819 |
Post Options
Thanks(0)
|
In any case the rating will be 2000W.
The better way is to use two 16 ohms drivers in parallel. This is more reliable.
|
|
kevinmcdonough
Old Croc Joined: 27 June 2005 Location: Glasgow Status: Offline Points: 3749 |
Post Options
Thanks(0)
|
I understand that by using parallel wiring the speakers will be more reliable, as one will still continue to play even if the other stops, but could this also be a downfall? If one speaker suddenly stops working and the other is playing, then the playing one will suddenly find itself plaing with double the cabinate volume behind it which, i would guess, would mean it may blow as well? At least in series, although you'd loose the volume from both drivers, you'd save the other driver from blowing? kev Edited by kevinmcdonough - 23 July 2006 at 7:18am |
|
Ben_Lawrance
Young Croc Joined: 12 January 2006 Location: Brighton Status: Offline Points: 919 |
Post Options
Thanks(0)
|
If one of your drivers blows whilst connected in parellel, the the amplifer would then see 16ohms as opposed to 8ohms. Therefore reducing the power into the cab. An amp that drives 2000w into 8ohms (is not just a big f**king amp) will drive 1000w into 16ohms. How many amps out there will drive 2KW into 8ohms anyway? Surely you'll be bridging the amp?
|
|
ceharden
The 10,000 Points Club Joined: 05 June 2005 Location: Southampton Status: Offline Points: 11776 |
Post Options
Thanks(0)
|
When I built some twin 15" subs recently, I used seperate chambers for
each driver so that if one blows the other will continue working
normally. The dividing piece also braces the cabinet in the
middle.
|
|
TomD
Registered User Joined: 22 July 2006 Status: Offline Points: 6 |
Post Options
Thanks(0)
|
They were hypothetical values, I'd probably be using something like 2x500/800w 16ohm parallel to make a total cabinet power handling of 1000/1500 watts.
|
|
JD01
Young Croc Joined: 23 August 2004 Status: Offline Points: 819 |
Post Options
Thanks(0)
|
I got one here....
Sometimes the coil of the speaker doesn't break the circuit when burnt, but short it. That means if you put two 4 ohm speakers in serial, and one fries, the other one would still run... at 4 ohms! So the ONE remaining speaker will get double the power the two speakers would get together, which would be around 3000W (for ONE speaker!). So it will blow easily.
|
|
super-hero
Old Croc Joined: 29 March 2005 Location: Middlesex Status: Offline Points: 2094 |
Post Options
Thanks(0)
|
I seem to recall reading somewhere that parallel is better, because of the affect it has on the amplifiers damping factor.
Someone else will know the specifics of this.
|
|
I'm not an animal, I'm a human being.
|
|
JD01
Young Croc Joined: 23 August 2004 Status: Offline Points: 819 |
Post Options
Thanks(0)
|
This is just a rumor without any scientific background. It has no effect on the damping factor. I can't belive there are actually engineers believing that nonsense.
|
|
TomD
Registered User Joined: 22 July 2006 Status: Offline Points: 6 |
Post Options
Thanks(0)
|
But if this happened while in parallel, the amp will short. I'm not really intending to be pushing drivers to breaking point, I was just confirming that two 1000w drivers in parallel would in fact result in a 2000w configuration. |
|
norty303
Old Croc Joined: 18 August 2004 Location: Eastbourne Status: Offline Points: 8806 |
Post Options
Thanks(0)
|
I think its more relevant that the change in cab volume for the one remaining driver will have an effect.
When i blew my BP6 drivers and looked at the VC's, both had evidence of burnout, however only 1 had any marks to indicate hitting back plate. I presumed that once one went the other also burnt but spent some time over excursing beforehand
|
|
My laser stuff: Frikkin Lasers
|
|
Tom Umney
Registered User Joined: 26 February 2004 Location: United Kingdom Status: Offline Points: 4954 |
Post Options
Thanks(0)
|
Two seperate chambers in the same box would be the key to using a dual driver sub.
|
|
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |