Schematics for Electro-Voice Zlx12-P |
Post Reply | Page <1 1819202122 32> |
Author | |
kedwardsleisure
Old Croc Joined: 20 January 2009 Location: Staffordshire Status: Offline Points: 4938 |
Post Options
Thanks(0)
|
it's because when you google for the diagrams this forum is no.1 in the results
|
|
Kevin
North Staffordshire |
|
nafo
New Member Joined: 14 April 2018 Status: Offline Points: 1 |
Post Options
Thanks(0)
|
never mind
Edited by nafo - 19 July 2019 at 1:08am |
|
Paul100
New Member Joined: 02 April 2018 Location: Netherlands Status: Offline Points: 2 |
Post Options
Thanks(0)
|
Hi there,
Is there anyone who's brain I can steal?? I had a ZLX 12P in for repair. THanks to the help of the schematics I managed to fix it. (Broken bridge and some minor components) After I build it together again it works great but I get an error message "Thermal`on the display after some volume. It does matters if I use more bass in the sound. If I turn down the volume the message disappears. I used new ordinary silicon isolation sheets after putting things together. The outside back black side of the speaker does not get very warm. In the pdf for the TDA 8953 (bass end stage amplifier) there is nothing written about a direct output indication of too high temperature only inside it regulates the output power. I cannot find any measuring schematics what could indicate this error message. Any help would be appriciated. Thanks Paul |
|
BTN
New Member Joined: 07 April 2018 Status: Offline Points: 3 |
Post Options
Thanks(0)
|
Hello Paul,
Thank you for sending me some info about EV ZLX 12P. It does help a bit. I don’t know what to say how to appreciate you. Again, thank you very much.
|
|
HTY
New Member Joined: 19 April 2018 Location: Myanmar Status: Offline Points: 1 |
Post Options
Thanks(0)
|
Hello Voron,
Please send me good q SMD of EV zlx 12p,fo1u288988 Thanks you very much from Myanmar kohanthuya@gmail.com
|
|
knuts2au
New Member Joined: 05 March 2018 Location: Australia Status: Offline Points: 6 |
Post Options
Thanks(0)
|
I have just finished rebuilding the power supply in a ZLx12P, replaced the FET, 150R Gate resistor, the driver IC and the 9x1R Drain resistors. Turned on and works ok, but i am concerned about the 1R Drain resistors, standard 1206 SMD's are only rated at 1/4W, 200V which i feel are way under rated. What would the spec's of the original resistors have been? The best i can find in 1206 size is 3watts.
PeterN |
|
Horta
New Member Joined: 02 May 2018 Location: Brazil Status: Offline Points: 3 |
Post Options
Thanks(0)
|
|
|
Horta
New Member Joined: 02 May 2018 Location: Brazil Status: Offline Points: 3 |
Post Options
Thanks(0)
|
hi voron, please i need power suplly the Zlx-12p eletro Voice. Thanks a lot. I livre in Brazil.
|
|
alopez
New Member Joined: 04 May 2018 Location: Rosario Status: Offline Points: 1 |
Post Options
Thanks(0)
|
Hi everybody. As many of who write in this thread, I came because I need the schematic of this speaker.
Please if Voron or anybody who has the schematic can send me one copy to my email (or post it here), I would be so grateful. My email: alopez92@hotmail.com Thank you so much in advance for your help. |
|
jcabrita79
New Member Joined: 04 May 2018 Status: Offline Points: 7 |
Post Options
Thanks(1)
|
Hello everyone
New to the forum, hope to learn from all of you! As a lot of people, i'm also looking for the ZLX-12P schematic as i have one on my bench right now! ;) If anyone can help me with this one it would be most apreciated! My email is jcabrita79@gmail.com. Thanks in advance, Jo£o
|
|
deeppetej
New Member Joined: 06 May 2018 Location: Winnersh Status: Offline Points: 3 |
Post Options
Thanks(0)
|
hi did you get the board sorted. I have the exact problem but all I done was power the thing up with no sound
|
|
deeppetej
New Member Joined: 06 May 2018 Location: Winnersh Status: Offline Points: 3 |
Post Options
Thanks(0)
|
Hello Voron
Can you Please Send me Zlx-12p Shematic Thank you djpetejames@hotmail.com
|
|
Post Reply | Page <1 1819202122 32> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |