|
sellenium mids |
Post Reply 
|
Page <12 |
| Author | |
tb_mike 
Old Croc 
Joined: 01 October 2004 Location: New Zealand Status: Offline Points: 2744 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 01 September 2006 at 9:35am |
|
With 3ways instead of two distortion will be lower overall too.
Guess you could try 2 x conical 8"s and see how it goes?
The centauri 8"s look a little hard to me to make!
|
|
 |
|
|
Mark James
Old Croc
Joined: 15 January 2006 Location: rig side Status: Offline Points: 5306 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 September 2006 at 8:50pm |
|
yes! and [fair play to him mind] he also wont sell me the plans [like i said i dont blame him! also hes been very helpfull with other projects]
er he does give enough info on there i guesse for you to work out similar plans [ie he talks you through the design phase in some fair amount of detail] that would look nice..... also i could run the 12" from 150hz<600hz [2 octaves] and the upper mid [be they 8" or 6" or 6.5" or any other number of inches] from there up to 2.4 khz [2 octaves] or even heigher,,,,
eventualy id have sub running an octave [30<60hz maybey with a slow rolloff from 60hz up........ ie overlapping the kick bass a little.
the kick bass running 1 1/2 octaves... 55hz<160hz ish
the low mids running an octave.. [150<600hz maybey slow rolloff on the top here, so the 12" still has noticeable out put up to say 1khz
upper mids playing between 2 and 2 1/4 octaves ie 600hz<2.4 or maybey even 3khz... then
the compression drivers only have to cover 2 octaves [ie 2.4/3khz <10khz] and the bullets can play the last octave........
could be realy nice and mean that transients [at almost any frequency] can be noticed..... [snare drums actualy punch almost as hard as a kick drum if its got enough guts behind it...]
shame the limeer 6" isnt arrayable or id be tempted to copy it... hmmmmm fibreglass, id like to use that!
cheers
markk.
|
|
|
insert silly sentence here
|
|
|
|
|
tb_mike
Old Croc
Joined: 01 October 2004 Location: New Zealand Status: Offline Points: 2744 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 September 2006 at 1:16am |
|
Itd be nice to not have the 60hz-160hz bin-Surely the low mid can be extended down to 110hz and bassbin up to there???
|
|
|
|
|
Mark James
Old Croc
Joined: 15 January 2006 Location: rig side Status: Offline Points: 5306 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 September 2006 at 1:25am |
|
hahaha ive already built the kick bins... [sellenium hb1505d1]
hmmmm not sure that the subs were gonna build will do much above 60hz for tekno/psy trance [the bulk of what we play...]
too many transients in the 60<100hz region id guess.
|
|
|
insert silly sentence here
|
|
|
|
|
Mark James
Old Croc
Joined: 15 January 2006 Location: rig side Status: Offline Points: 5306 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 September 2006 at 2:58am |
|
how heigh can a lab play when the programme material is tekno/psytrance??? i think 60hz tops?????
|
|
|
insert silly sentence here
|
|
|
|
|
tb_mike
Old Croc
Joined: 01 October 2004 Location: New Zealand Status: Offline Points: 2744 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 September 2006 at 9:58pm |
|
hm,120hz highest ive seen,alot seem to filter it below 100hz.If you filter it real sharp you might get away with a higher cutoff.
|
|
|
|
|
Post Reply
|
Page <12 |
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options