B&C 8PE21 horn |
Post Reply | Page <1 234 |
Author | |
doller
Young Croc Joined: 19 July 2014 Location: japan Status: Offline Points: 509 |
Post Options
Thanks(0)
|
I think the OP used one. And this is a really nice build loving the chunky look and the sp terminals. Very impressive. Edited by doller - 28 January 2019 at 3:56am |
|
luthier
Registered User Joined: 21 July 2013 Location: UK - London Status: Offline Points: 271 |
Post Options
Thanks(0)
|
With a circular saw yes, difficult and not very repeatable. However I would choose a good track saw like the TS55 or Mafell equivalent over all simarly priced table saws I have come across. I can get the same accuracy and just as clean a cut with my TS55 as I used to on a Altendorf panel saw. It does take a bit longer to setup and I sometimes need to make a jig or two but it is an incredibly versatile tool that I use daily. Also as a side note, it's not difficult to cut past 47 degrees with the right setup, whichever side of the blade. |
|
catalin
Registered User Joined: 02 April 2012 Location: London Status: Offline Points: 152 |
Post Options
Thanks(0)
|
concept-10
Young Croc Joined: 17 May 2016 Status: Offline Points: 1292 |
Post Options
Thanks(0)
|
stunning
|
|
catalin
Registered User Joined: 02 April 2012 Location: London Status: Offline Points: 152 |
Post Options
Thanks(0)
|
Contour
Young Croc Joined: 03 March 2004 Status: Offline Points: 620 |
Post Options
Thanks(0)
|
no damping added? Try to get hold of some ‘twaron’
|
|
catalin
Registered User Joined: 02 April 2012 Location: London Status: Offline Points: 152 |
Post Options
Thanks(0)
|
I will ad some,and do some measurements with and without damping.
|
|
JonB67
Young Croc Joined: 22 April 2016 Location: UK Status: Offline Points: 1376 |
Post Options
Thanks(0)
|
Awesome looking job!
|
|
luthier
Registered User Joined: 21 July 2013 Location: UK - London Status: Offline Points: 271 |
Post Options
Thanks(0)
|
Love it, they look great.
|
|
angus
Young Croc Joined: 10 August 2005 Location: TW, Kent, UK Status: Offline Points: 516 |
Post Options
Thanks(0)
|
Awesome work on these horns!
I am planning something similar but much simpler - more like the xtro mid horn section.
What method did you use to fill in the corner transitions from the baffle to the horn mouth here: Also, have you managed to test them and get some feedback on the design/approach? If they sound as good as they look they will be great!
|
|
They're complaining over there, but it's their fault!
|
|
catalin
Registered User Joined: 02 April 2012 Location: London Status: Offline Points: 152 |
Post Options
Thanks(0)
|
Hi there!
Very happy with the sound of the horns. Sharp,fast and plenty of spl. For those corners i used first wood chips mixt with glue for rough shape,after rough sanding i aplied some saw dust mixt with glue. Final stage ,some fine wood filler an fine sanding. You need to have big patience,it is time consuming. Before ewerything,i create a mesh from wire and some fine screws .
Edited by catalin - 29 November 2023 at 2:55pm |
|
Post Reply | Page <1 234 |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |