1850 horn measured plots |
Post Reply | Page <12 |
Author | |
Rog
New Member Rogers Archive Posts Joined: 23 March 2010 Status: Offline Points: 2166 |
Post Options
Thanks(0)
|
You place the speaker on the ground and then place the mic 2 meters away from the front of the speaker pointing at it. The mic must be on the ground with the capsule touching the ground. If you then feed the speaker 2.83 volts (presuming its an 8 ohm load) you will get a 1w/1m reading.
The mic must be at 2 meters as you gain 6dB from halfspace loading, but lose this 6dB by the mic being double the distance away from the speaker.
It dosen't take much of a distance to effect the reading if the mic is rasied of the floor, even at LF. The mic in some the the pics from the 1850 horn measurements looks like its about 1 meter from the floor, which would still effect the reading.
|
|
pfly
Old Croc Joined: 25 October 2007 Location: Helsinki, Fin Status: Offline Points: 2828 |
Post Options
Thanks(0)
|
The point wasn't being really scientific, but to test out the equipment (1850s and the measuring software) I wanted to see how different ways of stacking affects the response.
As I said we didn't drive them hard. Amp was bridged because it was wired that way already. Thanks for the info though, we'll try to be more accurate next time Edited by pfly - 11 May 2009 at 7:07am |
|
pfly
Old Croc Joined: 25 October 2007 Location: Helsinki, Fin Status: Offline Points: 2828 |
Post Options
Thanks(0)
|
Rog
Would that 60-70hz dip be there because of some cancellation stuff going on between the ground and the mike? |
|
Jake_Fielder
Old Croc Joined: 08 October 2007 Status: Offline Points: 4231 |
Post Options
Thanks(0)
|
If the height of the mic makes so much difference, wouldnt it be more usefull to have it the same height off the ground as an average persons height?? |
|
jethrocker
Old Croc Joined: 07 June 2006 Location: Chiapas, Mexico Status: Offline Points: 1942 |
Post Options
Thanks(0)
|
Read back Jake.. the mic is on the ground so that its loading conditions are the same throughout the frequency spectrum. If were at a given height, it would couple with the floor up to a given frequency, but not above that frequency. The idea is to take a groundplane (halfspace) reading.
That's the way I got it anyway. |
|
schiller
New Member Joined: 30 November 2007 Location: Greece Status: Offline Points: 8 |
Post Options
Thanks(0)
|
I just saw your plots , thanks a lot for sharing your efforts with us. Really a pity you didn't put that mic on the ground, but i believe the difference under 100 Hz wouldn't be much-if any. This is the only 1850 measurement available in the universe :-) What i see from the plot, is that in case of a single horn per side and in a room (yes there are people using this designs for hi-fi) bass from 50 Hz will be awesome. Maybe the 186 can better this, because of higher Qes driver, which loads better down low. Does the peak at cutoff indicate a smaller than needed back chamber, a larger throat or both?? Thanks again, greetings from Athens (Greece) Konstantinos |
|
Vaso_Bobinata
Registered User Joined: 21 May 2017 Location: Sofia BUL Status: Offline Points: 37 |
Post Options
Thanks(0)
|
Only ifi could see that graph the links are broken.
Thanks
|
|
Post Reply | Page <12 |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |