V18 cut out
Printed From: Speakerplans.com
Category: Plans
Forum Name: 1850 and 186 horns
Forum Description: Discussion / Questions about the 1850 and 186 horns
URL: https://forum.speakerplans.com/forum_posts.asp?TID=68409
Printed Date: 18 April 2024 at 1:20am
Software Version: Web Wiz Forums 12.06 - https://www.webwizforums.com
Topic: V18 cut out
Posted By: Amplighting&sound
Subject: V18 cut out
Date Posted: 27 June 2012 at 8:26pm
| Can any one help i need to make the cut out in my 1850s bigger for the v18 as its bout 5mm to small any help would be lovely |
Replies:
Posted By: hmaudio
Date Posted: 27 June 2012 at 8:50pm
|
on the pdf i have for the v18-1000 it says rear mounted is 425mm and front mounted is 430mm hope this helps cheers Adam ------------- Nottingham based cab builder. https://www.facebook.com/HMAudio-154352667920145/?ref=bookmarks This account is used by 2 people. |
Posted By: Amplighting&sound
Date Posted: 27 June 2012 at 9:52pm
| Thank u m8 but i hav that info its just the cut out needs to be bigger but how do u get a routa in to do it please help lol |
Posted By: hmaudio
Date Posted: 27 June 2012 at 10:13pm
|
if the cab is already built its going to be hard to make the cut out bigger. ------------- Nottingham based cab builder. https://www.facebook.com/HMAudio-154352667920145/?ref=bookmarks This account is used by 2 people. |
Posted By: Amplighting&sound
Date Posted: 28 June 2012 at 6:39am
| True dem cab is allready made would it hurt if cut out was 5mm to small would this make cone rub |
Posted By: Amplighting&sound
Date Posted: 28 June 2012 at 9:52pm
| Any 1 got any input |
Posted By: Vert
Date Posted: 28 June 2012 at 10:24pm
and a Rotary rasp + alot of patience  ------------- Box builder, pm for quote |
Posted By: Amplighting&sound
Date Posted: 28 June 2012 at 10:59pm
| Do well thank u |
Posted By: Amplighting&sound
Date Posted: 29 June 2012 at 9:08pm
| Hello again just tryed the rasp and its a very slow process does any one hav any other ideas please |
Posted By: infrasound
Date Posted: 29 June 2012 at 9:23pm
|
If it's only 5mm you should be able to use a chamfer bit on a router. Set it so that the bearing just about catches the inside wood.
|
Posted By: infrasound
Date Posted: 29 June 2012 at 9:27pm
Like so |
Posted By: Amplighting&sound
Date Posted: 29 June 2012 at 9:30pm
| Thank u infa but my prob is i can only gt my trimer round the bottom half of cut out as the chamber gts narrow at the back ? |
Posted By: infrasound
Date Posted: 29 June 2012 at 9:31pm
|
Oh, just seen it's inside an 1850.. Right angled rasp it is! Find a small child and get them to do it for a mars bar
 |
Posted By: infrasound
Date Posted: 29 June 2012 at 9:49pm
|
Otherwise an angle grinder with an very low grit wheel. (<25) I think you can also get wood wheels.
|
Posted By: Amplighting&sound
Date Posted: 29 June 2012 at 10:19pm
| Do well will try the grinder just dont want it to look messi |
Posted By: bee
Date Posted: 29 June 2012 at 10:42pm
| can you using a jigsaw turn jig saw upside down and slowly notch out loads of lines 5mm deep then use a very sharp chisel to knock them out..... hope you get what i mean........ |
Posted By: bee
Date Posted: 29 June 2012 at 10:45pm
| should of said with an extended blade, ill do a quick google search for you and find a link to what i mean..... |
Posted By: bee
Date Posted: 29 June 2012 at 10:46pm
|
http://www.google.co.uk/products/catalog?hl=en&safe=off&rlz=1C2AFAA_en-GBGB434GB455&q=jig+saw+blade&bav=on.2,or.r_gc.r_pw.r_qf.,cf.osb&biw=1280&bih=685&um=1&ie=UTF-8&tbm=shop&cid=7529241557775812567&sa=X&ei=9SHuT_GzFYz58QOc5dCqDQ&ved=0CH8Q8gIwAw" rel="nofollow - http://www.google.co.uk/products/catalog?hl=en&safe=off&rlz=1C2AFAA_en-GBGB434GB455&q=jig+saw+blade&bav=on.2,or.r_gc.r_pw.r_qf.,cf.osb&biw=1280&bih=685&um=1&ie=UTF-8&tbm=shop&cid=7529241557775812567&sa=X&ei=9SHuT_GzFYz58QOc5dCqDQ&ved=0CH8Q8gIwAw
this way you can get the jigsaw in there...... just take your time....... as you will be doing it free hand with the jigsaw in free air..... i.e. base not touching wood.....
|
Posted By: Vert
Date Posted: 29 June 2012 at 10:47pm
------------- Box builder, pm for quote |
Posted By: Amplighting&sound
Date Posted: 29 June 2012 at 10:57pm
| Ok nice one boys ya get what ya mean thank u will try it first thing in morning |
Posted By: Amplighting&sound
Date Posted: 30 June 2012 at 8:16pm
| Hello people of the 1850s lol 5 down 3 to go best way is routa half and grider with flat wheel |
Posted By: Amplighting&sound
Date Posted: 01 July 2012 at 6:49pm
| Hello all 8 are now dun just need to wire them up ready for saturday |