1850 Cut list - A gift to you
Printed From: Speakerplans.com
Category: Plans
Forum Name: 1850 and 186 horns
Forum Description: Discussion / Questions about the 1850 and 186 horns
URL: https://forum.speakerplans.com/forum_posts.asp?TID=76596
Printed Date: 27 March 2026 at 8:53am
Software Version: Web Wiz Forums 12.08 - https://www.webwizforums.com
Topic: 1850 Cut list - A gift to you
Posted By: Venny
Subject: 1850 Cut list - A gift to you
Date Posted: 26 February 2013 at 4:36am
|
Thought this might save anyone else the hassle I went through. Uses two 2440 x 1220 x 18mm sheets. Necessary panels have the appropriate hang over accounted for to the allow for mitre angles. Just realized I missed the access panel out but I'm sure you can work that one out for yourselves! http://imageshack.us/photo/my-images/839/sheetlayout.jpg/" rel="nofollow"> http://imageshack.us/photo/my-images/267/sheet02measurements.jpg/" rel="nofollow"> http://imageshack.us/photo/my-images/820/panelid2.jpg/" rel="nofollow"> ------------- Predominant Culture Sound System - Roots and Culture |
Replies:
Posted By: ermita
Date Posted: 26 February 2013 at 5:21am
|
Posted By: b grade
Date Posted: 26 February 2013 at 6:54am
| Interesting. I like how you did brace 13. I made mine the same shape as on the plan, but yours helps to support that pannel 10. The joint between panel 9 and 10 on mine is by far the weakest joint in my build, as it is really hard to screw those two panels together from the dead space. I suppose I could have done so before installing them, but I did not think of doing that when I was building. |
Posted By: Venny
Date Posted: 26 February 2013 at 4:12pm
|
Thats the exact reason brace 13 is bigger and a stupid shape as apposed to the original plans. Got a few to get through so expect some build pics soon ------------- Predominant Culture Sound System - Roots and Culture |
b grade wrote:
Couldn't help but feel panels 9 & 10 wouldn't be solid enough without it.Posted By: b grade
Date Posted: 26 February 2013 at 5:14pm
|
The thing I did differently from the plans, was to lower the panel at the bottom of the chamber slightly as it seemed to be right where I wanted the bolts to go through to hold on the access panel. I still attached it to the same corner at the front, but instead of having it go flush with the door, it went straight perpendicular from the back wall which was down about 2.5 cm from the batten edge. Slightly increases the chamber volume, but made no difference in sim. Good luck with the building. :)
|
Posted By: Venny
Date Posted: 26 February 2013 at 7:07pm
|
Yeah I noticed that when revising the plans, I figured I'd get around the problem by using appropriate pilot holes and cutting bolts down so they're only as long as they need to be. So the bolts will go through the access panel, through the 'batons' that hold the access panel in place, through the t-nut and then into the panel that acts as the bottom of the chamber by only a few milliliters. ------------- Predominant Culture Sound System - Roots and Culture |
Posted By: b grade
Date Posted: 26 February 2013 at 7:41pm
| That should work, just be careful not to cross the thread, because those t nuts will be permanent. |
Posted By: ClackS02
Date Posted: 19 March 2013 at 2:11pm
|
you are one beautiful man ! I have been searching HIGH AND LOW for this !!! <3 thanks dude
|
Posted By: Venny
Date Posted: 23 March 2013 at 5:30pm
Glad my efforts have helped someone! ------------- Predominant Culture Sound System - Roots and Culture |
Posted By: BassPhysics
Date Posted: 27 March 2013 at 12:55am
| just what i needed to find dude |
Posted By: Dubterrorist
Date Posted: 17 October 2015 at 3:44pm
| Can you tell me what tools I'll need to build some of these please mate. |
Posted By: b grade
Date Posted: 17 October 2015 at 6:17pm
|
For the baffle, you can cut the driver circle with either a jigsaw or a router and jig. Personally I just use a jigsaw unless the circle is going to be visible. You still need the router for the roundover at the edges though, and then you need a straight cut bit and a round over bit. For the panels, you can do a lot of it with a hand held circular saw and a good straight edge, though a festool type is better. The bevel angles require some precision. My Table saw works best for that, but if you have a really good hand held (I don't) it may be fine. You need a drill/driver. You need good strong glue. Much debate about the best glue. Depending what you go with, you may need a caulking gun. Some kind of sander and sand paper of various grit size. Extra coarse will remove excess wood but be careful not to wreck the veneer with it, and fine will smooth the surface before painting. You will need some clamps. Big and small. Lots of clamps, especially if you are making more than one at a time, which everyone does pretty much. Meter stick and or Measuring tape. I also like to have some cargo straps to use where clamps are awkward. Putty knife and woodfiller, or something like it (Glue and sawdust, autobody filler etc. Much debate on this too) to fill the screw holes. Contersink bit to allow the screws to go below grade. Some screws can pull in by themselves, but this can buckle the veneer so I like to use the bit. Whatever painting supplies you need for whatever paint you use (much debate again). Soldering gun and solder supplies. Maybe a staple gun if you use any wadding. Lots of sharp pencils, because they keep disappearing (maybe that is just me). Do it outside if you can. If you must do it inside, you need ventilation but also you want an airtight seal to the rest of the house unless you really love dusting. The driver and access panel will require bolting (much debate, I use the dreaded Tee nuts). Gasket tape for the access panel, and something to cut it. |
Posted By: Simmo1990
Date Posted: 07 September 2016 at 3:59pm
|
Hi mate. I'm trying to get the cut list but the picture are not visable. Any chance you could send the over to me. Cheers |
Posted By: Vaso_Bobinata
Date Posted: 03 November 2018 at 4:37pm
|
Boys I cannot open the images. Maybe somebody has them. Thanks
|
Posted By: djeddie
Date Posted: 03 November 2018 at 8:32pm
|
The original post is from five years ago, it's no surprise they've disappeared. ------------- Chas n Dave : it's like Drum and Bass but with beards. E=mc² ±3dB |
Posted By: Vaso_Bobinata
Date Posted: 04 November 2018 at 6:15am
Not really surprised bud, just need the stuff. I will be surprised if somebody got them on DWG. :))))
|
Posted By: Dub Specialist Sound
Date Posted: 04 November 2018 at 12:13pm
|
work it out pretty simple tbh I had too ------------- Musical Roots Reggae Vibration is Life! for music is sound...sound is vibration...vibration is energy... and energy begets life. Therein lies my passion!...MUSIC IS LIFE... |