|
outline t6.5 /powersoft digam7000 service manual |
Post Reply 
|
Page <1234 8> |
| Author | |
noobsound 
Registered User 
Joined: 28 March 2008 Location: Romania Status: Offline Points: 67 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 08 December 2009 at 10:08pm |
|
Hello. The amplifier is now repaired and runs like new. A friend of mine gave me the number of the guy who was in charge of repairing outline amps in Romania. The amp did not have anything burned in it , it was just some corosion problems on some part due to the fact that somebody managed to spill some cofee or juice in it.
Me and the user Adircf tested the amp a few hours back it it works fine.
|
|
 |
|
|
Melaineamp
New Member 
Joined: 05 November 2008 Status: Offline Points: 3 |
Post Options
Thanks(0)
Quote Reply
Posted: 11 December 2009 at 8:06am |
|
can send to melianeamp@gmail.com ? I meet a problem on t11.
|
|
|
|
|
noobsound
Registered User
Joined: 28 March 2008 Location: Romania Status: Offline Points: 67 |
Post Options
Thanks(0)
Quote Reply
Posted: 12 December 2009 at 11:54am |
|
@ melaineamp u want the schematics of the power suply?
|
|
|
|
|
Melaineamp
New Member
Joined: 05 November 2008 Status: Offline Points: 3 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 December 2009 at 9:22am |
|
@ noobsound I want the schematics of amplification. thanks
|
|
|
|
|
soundgodz
New Member
Joined: 14 April 2010 Location: Portland oregon Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: 15 April 2010 at 4:49am |
|
Hey noodsound can i get the Digam 7000 schematics? Thanks kwruecker@qwest.net |
|
|
|
|
Bryan M
Old Croc 
Joined: 17 July 2004 Location: England/Belgium Status: Offline Points: 2223 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 April 2010 at 4:33am |
|
Do all you guy genuinely have problems with your powersofts or do you just want to copy the design?
|
|
|
|
|
soundgodz
New Member
Joined: 14 April 2010 Location: Portland oregon Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 April 2010 at 4:27pm |
|
Bryan Yes I have a problem with the input level.' works fine and then will go full blast like the ground is coming off on the level pot. I opened and found the ribbon that connects the front panel has a broken header. I also saw a pile of dust bridging th legs of the level pot. the input circuit board was covered with a fine grit i cleaned all and will test again. have found this to be a reliable and it still works despite this problem. I still have not recieved the service manual from anyone yet. |
|
|
|
|
serhatkay
New Member
Joined: 12 May 2010 Location: Turkiye Status: Offline Points: 1 |
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 11:41pm |
|
hello Basil can you send "digam 7000 service manual" to me
thank you very much
best regards
Serhat Kaya
ProAudio/Electronic Technician - Turkiye
|
|
|
|
|
abeltronics
Registered User
Joined: 16 July 2009 Location: Norwich Status: Offline Points: 265 |
Post Options
Thanks(0)
Quote Reply
Posted: 15 May 2010 at 12:35pm |
|
http://www.abeltronics.co.uk - Electronic Engineers
|
|
|
|
|
rona1977
New Member
Joined: 18 May 2010 Status: Offline Points: 1 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 May 2010 at 10:19am |
|
Hi! Can you send the diagram to me too?
rona1977@libero.it |
|
|
|
|
Oldmaelstrom
Registered User
Joined: 07 October 2009 Status: Offline Points: 15 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 May 2010 at 5:05pm |
|
and me please switchlab@gmail.com
Thanks |
|
|
|
|
soc15
New Member
Joined: 08 July 2010 Status: Offline Points: 1 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 July 2010 at 7:39am |
|
Me too please... For powersoft digam7000 service manual somcha.P@gmail.com |
|
|
|
|
Post Reply
|
Page <1234 8> |
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options